Certified
Copyright 2004-2017 Control4 Corporation. All rights reserved.
The B&W Group
Rotel
Rotel RA-1570
RA-1570 [DriverWorks]
12/30/2013 10:08 AM
02/24/2017 2:52 PM
8
devices_sm\receiver.gif
devices_lg\receiver.gif
lua_gen
serial
DriverWorks
receiver
media_player
media_player
False
True
True
True
True
True
True
True
True
True
1
10
True
False
115200 8 none 1 none 232
False
True
True
True
True
True
True
0
0
0
True
True
False
1
6
Serial RS-232
1
True
False
False
True
RS_232
3000
6
XLR
6
True
False
False
True
STEREO
3001
6
PHONO
6
True
False
False
True
STEREO
3002
6
FRONT USB
6
True
False
False
True
2
True
STEREO
True
3003
6
PC-USB
6
True
False
False
True
3
True
STEREO
3004
6
CD
6
True
False
False
True
STEREO
3005
6
TUNER
6
True
False
False
True
STEREO
3006
6
AUX 1
6
True
False
False
True
STEREO
3007
6
AUX 2
6
True
False
False
True
STEREO
3008
6
COAX 1
6
True
False
False
True
DIGITAL_COAX
3009
6
COAX 2
6
True
False
False
True
DIGITAL_COAX
3010
6
OPTICAL 1
6
True
False
False
True
DIGITAL_OPTICAL
3011
6
OPTICAL 2
6
True
False
False
True
DIGITAL_OPTICAL
4000
6
MAIN OUTPUT
6
False
False
False
True
STEREO
SPEAKER
4002
6
FRONT USB Proxy Output To RECEIVER [REQUIRED]
6
False
False
False
True
2
True
SPEAKER
True
STEREO
True
4003
6
PC-USB Proxy Output To RECEIVER [REQUIRED]
6
False
False
False
True
3
True
SPEAKER
True
STEREO
True
5001
6
Receiver
2
False
False
False
False
RECEIVER
5002
6
FRONT USB
2
False
False
False
False
MEDIA_PLAYER
5003
6
PC-USB
2
False
False
False
False
MEDIA_PLAYER
7000
6
MAIN OUTPUT Audio/Video End-Point
7
False
True
False
True
AUDIO_SELECTION
AUDIO_VOLUME
AlwaysOn
0
0
False
115200 8 none 1 none 232
Control4 certified on 2/28/2017 for software released version: 2.9.1
RA-1570 DriverWorks 2-Way Serial Driver
Driver written by the B&W Group.
SERIAL PROTOCOL:
3 wire RS-232C protocol
115200 baud, 8 data bits, 1 stop bits, no parity, no flow control
Uses a straight through type DB9 serial cable.
Notes: This driver written using the an ASCII based protocol that was updated with Main Software V1.1.8.
Unit must be running this version or higher to work with this driver.
The RED button has been programmed for Shuffle mode. The GREEN button is programmed for Repeat.
A NOTE ABOUT POWER CONTROL:
This driver does not use the ON or OFF commands. The CONNECT_OUTPUT and DISCONNECT_OUTPUT codes are used to power the unit on and off. These commands are sent to the device from the Control4 system when you select a source, or turn the room off. So if testing the driver from the emulator within Composer, it is intended that the unit does not respond to the ON or OFF buttons here. If power control is needed outside of the normal flow of source selection or room on/off, use the provided POWER_ON and POWER_OFF driver-specific commands.
SET BALANCE CONTROL RANGES:
01-49 - Shift balance left, with 01 being max left and 49 being closest to centered.
50 - Centered (no balance adjustment).
51-100 - Shift balance right, with 51 being closest to center and 100 being max right.
TECHNICAL SUPPORT:
For support with this driver, you may contact The B&W Group at techsupport@bwgroupusa.com.
AC POWER NOTE:
Note that this product is designed to power up fully upon receiving AC power, so in the event of a power outage the unit would power on once AC power has been restored. With this in mind, it is recommended to set the POWER ON MAX VOLUME setting in the setup menu to a low or MIN setting to ensure if the system does power on as a result of a power interruption that it does not turn on at a high volume.
SYSTEM VARIABLES:
This driver includes SPEAKER_A_OUTPUT and SPEAKER_B_OUTPUT system variables that track the state of the speaker outputs for use in programming. Value is either ON or OFF.
Updated 1/17/2014
- Minor fixes - removed some extraneous commands left in from a different driver (ENTER_LONG, MEMORY)
- Added TONE_ON and TONE_OFF commands to enable/disable Tone Controls. These commands require Main SW V1.2.9 or higher to utilize.
Updated 1/31/2014
- Fixed the Power On Delay property so it is effective now. This delay is after Power On, but before any additional commands are sent to the device.
- Added a new Property to allow a delay before the initial Power On command is sent.
Updated 8/11/2014
- Fixed a bug that prevented internet radio streams from the Control4 controller to work properly when connected to the receiver
Updated 4/30/2015
- Minor fixes and updates to accomodate RS232 changes made with main SW V1.3.8
Updated 12/22/2016
- Added POWER_ON and POWER_OFF driver-specific commands to allow access to power control commands via Programming.
Destroy All Timers
Destroy Timers
CANCEL
Returns to Home menu
DOWN
OSD Cursor Down
ENTER
OSD Enter
LEFT
OSD Cursor Left
MENU
OSD Menu
RANDOM
Random
REPEAT
Repeat
RIGHT
OSD Cursor Right
UP
OSD Cursor Up
DIMMER
Display Dimmer Toggle
TONE_ON
Tone Controls On
TONE_OFF
Tone Controls Off
BASS_RESET
Reset bass controls to 0 (flat)
TREBLE_RESET
Reset treble controls to 0 (flat)
BALANCE_RESET
Reset balance to 0
SPEAKER_A
Toggle Speaker A output
SPEAKER_B
Toggle Speaker B Output
POWER_ON
Power On
POWER_OFF
Power Off
Command Delay-Milliseconds
RANGED_INTEGER
false
250
100
2500
Maximum Volume Level
RANGED_INTEGER
false
80
50
100
Delay Before Issuing Power On Command-Seconds
RANGED_INTEGER
false
0
0
60
Power On Delay-Seconds
RANGED_INTEGER
false
2
0
25
Volume Ramp Delay-Milliseconds
RANGED_INTEGER
false
200
50
500
Poll Timer Delay-Seconds
RANGED_INTEGER
false
60
10
500
Debug Mode
LIST
false
Off
- Off
- Print
- Log
- Print and Log
Audio/Video
Control4 certified on 2/28/2017 for software released version: 2.9.1