Copyright 2004-2012 Control4 Corporation. All rights reserved. The B&W Group Rotel Rotel RC-1580 RC-1580 [DriverWorks] 07/08/2010 3:33 PM 01/31/2014 9:54 AM 3 devices_sm\receiver.gif devices_lg\receiver.gif lua_gen serial DriverWorks receiver False True False True False True 2 8 True False 19200 8 none 1 none 232 False False 0 1 6 Serial RS-232 1 True False False True RS_232 3000 6 PHONO 6 True False False True STEREO 3001 6 CD 6 True False False True STEREO 3002 6 TUNER 6 True False False True STEREO 3003 6 AUX 1 6 True False False True STEREO 3004 6 AUX 2 6 True False False True STEREO 3005 6 AUX 3 6 True False False True STEREO 3006 6 TAPE 1 6 True False False True STEREO 3007 6 TAPE 2 / BYPASS 6 True False False True STEREO 4000 6 MAIN OUTPUT 6 False False False True STEREO 4001 6 RECORD OUTPUT 6 False False False True STEREO 5001 6 Receiver 2 False False False False RECEIVER 7000 6 MAIN OUTPUT Audio/Video End-Point 7 False False False True AUDIO_SELECTION AUDIO_VOLUME 7001 6 RECORD OUTPUT Audio/Video End-Point 7 False False False True AUDIO_SELECTION AlwaysOn 0 0 False 19200 8 none 1 none 232 RC-1580 DriverWorks 2-Way Serial Driver Driver written by the B&W Group. Any bugs please report to msheehan@bwgroupusa.com SERIAL PROTOCOL: 3 wire RS-232C protocol 19200 baud, 8 data bits, 1 stop bits, no parity, no flow control Uses an RJ45 type connector to DB9 connector cable. Pin Settings: RJ45 Side: Pin 3 TX, Pin 5 RX, Pins 4 & 6 Gnd. DB9 Side: Pin 3 TX, Pin 2 RX, Pin 5 Gnd. Notes: This driver does not use the ON or OFF Proxy commands to control power to the unit. It uses the SET_INPUT command and DISCONNECT_OUTPUT commands to power the unit on or off, respectively. The TAPE2 input is the Theater Bypass input, so to select bypass mode you can just select the Tape 2 input, or use the BYPASS_ON/BYPASS_OFF commands. Revised 10/25/11: Added a volume ramp timer to help with volume ramping issues. If ramping issues occur increase the delay timer which should help. Also fixed debug mode to ensure it is off by default, which should improve speed of the driver. Revised 2/8/12: Added a feedback timer to help reduce potential issues from too much feedback data reducing system performance. Revised 9/21/2012: - Complete revision of how commands are received/processed, the process is now faster and more streamlined. Volume ramping for example should now be faster and more responsive. - Fixed a bug that could cause the unit to occasionally not update feedback status. Revised 1/31/2014 - Fixed the Power On Delay property so it is effective now. This delay is after Power On, but before any additional commands are sent to the device. - Added a new Property to allow a delay before the initial Power On command is sent. Destroy All Timers Destroy Timers BYPASS_OFF Turns Theater Bypass Mode Off BYPASS_ON Turns Theater Bypass On BYPASS_TOGGLE Toggles Theater Bypass Mode Command Delay-Milliseconds RANGED_INTEGER false 250 100 2500 Debug Mode LIST false Off Off Print Log Print and Log Delay Before Issuing Power On Command-Seconds RANGED_INTEGER false 0 0 60 Power On Delay-Seconds RANGED_INTEGER false 2 0 25 Volume Ramp Delay-Milliseconds RANGED_INTEGER false 200 50 500 Audio/Video