Suporte Rotel
Estamos aqui para ajudá-lo com qualquer dúvida que possa ter sobre seus produtos e dispositivos Rotel, ou podemos oferecer uma visão sobre o mundo do som e da qualidade do som.
VOCÊ TEM UMA PERGUNTA?
PERGUNTAS FREQUENTES
I'm not getting sound from my center or rear channel speakers when watching a DVD. Why?
Your DVD players digital audio settings may be set to only output PCM two channel stereo. To change the mode to Dolby Digital, stop the disc and remove it from the DVD player, then follow the instructions below depending on your DVD player:
- RDV-1092 / RDV-1093: With the disc stopped or no disc loaded, push "Set Up" on the remote control to display the Setup menu, then select Audio setup. Change the Digital Audio Output to Multichannel.
- RDV-1045: With the disc stopped or no disc loaded, push "Set Up" on the remote control for a few seconds to display the Setup menu, then select the Audio tab (speaker icon). Change the Digital Audio Output to Stream/PCM.
- RDV-1040 / RDV-1050: Push "Choice" on the remote control for a few seconds to display the Setup menu, then select the Audio tab (speaker icon). Change the Digital Audio Output to Stream/PCM.
- RDV-985 / RDV-1080: Push "On-Screen" on the remote control and select the Preference 2 tab. Then change the output to Stream/PCM.
- RDV-995: Press and hold the "shift" button and press the "choice" button to access the on-screen display. Select the Audio tab, and change the output to Stream/PCM.
Please note that you need a Dolby Digital/DTS processor and amplifier or receiver to enjoy 5.1 surround sound.
Modelos aplicáveis:
RDV-1040 | RDV-1045 | RDV-1050 | RDV-1080 | RDV-1092 | RDV-1093
If my Rotel CD player is connected digitally with the coaxial output, will it still decode HDCD?
Using the digital output of the CD player will bypass all digital-to-analog decoding of the CD, including the HDCD decoding. As such, the only way to gain the benefits of HDCD when connecting digitally is if the receiver/processor/DAC you are connecting to includes HDCD decoding. Rotel’s RSP-1066 and RSP-1098 Processors, and RSX-1055 and RSX-1065 receivers do include HDCD decoding. Otherwise, the only way to get the benefit of HDCD is via the analog RCA connections.
Modelos aplicáveis:
RCC-1055 | RCD-1070 | RCD-1072
Is there a way to just watch TV without turning on my entire home theater system?
Yes - many Rotel surround processors and receivers with HDMI include a feature called "Standby passthrough" that will allow you to pass an HDMI audio/video signal through the Rotel system even while it is in standby. This would allow you to watch TV using just the TV speakers instead of turning on the theater, for example.
Modelos aplicáveis:
RAP-1580 | RSP-1572 | RSP-1576 | RSP-1582 | RSX-1562
Is there a way to manually eject a jammed disc from the CD player?
In rare cases a situation may arise in which a disc may become stuck in the slot loading CD mechanism. The following procedure can be used to manually extract a disc from the mechanism in this case.
- Remove the top cover of the unit and locate the small white eject gear located on the rear left side of the CD mechanism.
- Use a small Phillips head screwdriver to turn the gear counterclockwise until the disc is ejected. The back of the mechanism near the screw is labeled showing the direction the gear should turn in order to eject.
Modelos aplicáveis:
RCD-12 | RCD-1520 | RCD-1570 | RCX-1500
Is there an IR remote code available to Power On or Off for Rotel CD players?
Rotel CD player models in the 10 and 02 series did not have an IR code for Power on or off, however to remotely turn the unit on and off the 12 Volt trigger input on the back panel of the unit can be used with any Rotel and many other preamplifiers and receivers to trigger the CD player on and off with the preamplifier. Alternatively, if the preamplifier has a switched AC outlet this can be used also to power the CD player on and off.
Modelos aplicáveis:
RCC-1055 | RCD-06 | RCD-1070 | RCD-1072
Is there any way to dim or turn off the front display?
There is no display dimmer on these models; however it is possible to turn off the front display by pressing and holding the Menu button on the remote for 5 seconds. The display will then turn off, reappearing temporarily whenever any change is made to the system. To turn the display back on, press the Menu button on the remote again, or power the unit off. The display will be reset to normal when the unit is powered back on.
Modelos aplicáveis:
RSP-1066 | RSP-1068 | RSP-1069 | RSP-1098 | RSP-1570 | RSP-1572 | RSX-1055 | RSX-1056 | RSX-1057 | RSX-1058 | RSX-1065 | RSX-1067 | RSX-1550 | RSX-1560 | RSX-1562
Is there any way to disable the subwoofer output in 2 Channel stereo, but leave it active in Dolby Digital and dts?
The original designs of the RSP-1066, RSX-1055 and RSX-1065 did not allow this to be done, short of turning off the subwoofer in the Speaker setup menu before using 2 Channel mode. However, the ability to disable the subwoofer output for different surround modes, including stereo, has been added in a later software update for the unit.
With software versions listed below and beyond, the subwoofer output can be disabled by accessing the SUB SETUP menu from the OSD, and for each surround mode the subwoofer level can be adjusted to +10dB and –9dB. Lowering the subwoofer level below –9dB will display OFF, and will disable subwoofer output for this DSP mode. Using this method, the subwoofer output can be separately enabled or disabled for 2, 5, and 7 Channel Stereo; the 4 Music Modes; all Dolby and all dts modes.
- RSP-1066: V1.48 or V2.24 and later
- RSX-1055: V1.48 or V2.24 and later
- RSX-1065: V1.55 or V2.22 and later
Modelos aplicáveis:
RSP-1066 | RSX-1055 | RSX-1065
Is there any way to disable the subwoofer output in 2 Channel stereo, but leave it active in Dolby Digital and dts?
Yes, you can make a change such as this by using the ADVANCED SPEAKER settings. This settings menu allows you to define custom speaker configurations and bass management settings based on the surround mode. So you could in theory set up your receiver to play Dolby Digital and dts soundtracks using all SMALL loudspeakers with a Subwoofer, and configure Stereo sources to play with just 2 LARGE front speakers and no subwoofer.
The Advanced Speaker settings menu is located with the SPEAKER setup menu of the On Screen Display.
Modelos aplicáveis:
RSP-1068 | RSP-1069 | RSP-1098 | RSP-1570 | RSP-1572 | RSP-1582 | RSX-1056 | RSX-1057 | RSX-1058 | RSX-1067 | RSX-1550 | RSX-1560 | RSX-1562
My computer doesn't have a serial port - how can I update the Rotel software?
You will need a USB to Serial Port Adapter. There are many different adapters on the market today that plug into a USB port on the computer and will function as a serial port for connecting to a Rotel component for updating.
It is important when selecting an adapter to make sure you install the latest available drivers for the adapter to ensure that the upgrades go smoothly. This is particularly important when using the adapters on newer operating systems such as Windows 8. We recommend ideally checking the website of the manufacturer for the latest drivers before connecting and installing the adapter.
Modelos aplicáveis:
A12 | RA-11 | RA-12 | RA-1570 | RC-1570 | RCD-1570 | RCX-1500 | RDD-1580 | RDG-1520 | RKB-850 | RKB-8100 | RKB-D850 | RKB-D8100 | RSP-1066 | RSP-1068 | RSP-1069 | RSP-1098 | RSP-1570 | RSP-1572 | RSX-1055 | RSX-1056 | RSX-1057 | RSX-1058 | RSX-1065 | RSX-1067 | RSX-1550 | RSX-1560 | RSX-1562 | RT-09 | RT-1084 | RX-1052
